SPACAR Wiki

User Tools

Site Tools

You are here: start » optimization
optimization

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
optimization [2018/09/18 10:32]
mark.naves 		optimization [2022/01/12 13:41] (current)
jan.dejong
Line 6: Line 6:
  
 <code matlab run_sim.m> <code matlab run_sim.m>
-function cost = run_sim(P, Silent)% EXAMPLE SCRIPT FOR RUNNING SPACAR LIGHT+function [cost, out] = run_sim(P, Silent)% EXAMPLE SCRIPT FOR RUNNING SPACAR LIGHT
 if nargin == 1 if nargin == 1
     Silent = true; %run in silent mode when called by optimizer     Silent = true; %run in silent mode when called by optimizer
Line 20: Line 20:
 stressmax = 300e6; %Max stress [MPa] stressmax = 300e6; %Max stress [MPa]
 Mmax = 2.5; %Max actuation moment [Nm] Mmax = 2.5; %Max actuation moment [Nm]
-Stroke = 0.5; %Max stroke+Stroke = 0.5; %Max stroke [Rad]
  
  
 %% NODE POSITIONS %% NODE POSITIONS
 %           x y z %           x y z
-nodes = [   0 0 0;      %node 1  +nodes = [   0 0 0;    %node 1  
             0 H 0;    %node 2               0 H 0;    %node 2  
-            B H 0;  %node 3+            B H 0;    %node 3
             B 0 0];   %node 4             B 0 0];   %node 4
  
Line 60: Line 60:
 eprops(1).orien    = [0 0 1];          %Orientation of the cross-section as a vector pointing along "width-direction" eprops(1).orien    = [0 0 1];          %Orientation of the cross-section as a vector pointing along "width-direction"
 eprops(1).nbeams   = 2;                %Number of beams used to model this element  eprops(1).nbeams   = 2;                %Number of beams used to model this element 
-eprops(1).flex     = 1:6;            %Model out-of-plane bending (modes 3 and 4) as flexible+eprops(1).flex     = 1:6;              %Consider all deformation modes (1 to 6) as flexible
 eprops(1).color    = 'grey';           %Color eprops(1).color    = 'grey';           %Color
 eprops(1).opacity  = 0.7;              %Opacity eprops(1).opacity  = 0.7;              %Opacity
Line 99: Line 99:
 </code> </code>
  
-An example to conduct the optimization is provided below, taking into account additional boundary conditions on the design parameters of the cross-hinge. See matlab's documentation on''fmincon'' for more information.+An example to conduct the optimization is provided below, taking into account additional boundary conditions on the design parameters of the cross-hinge. See matlab's documentation on ''fmincon'' for more information.
  
-</code matlab optimization.m>+<code matlab optimization.m>
 %filename %filename
 simulation = @run_sim; simulation = @run_sim;
  
 %starting point %starting point
-x0 = [0.1 0.1 50e-3 0.2e-3]';+x0 = [0.1;  0.1;  50e-3; 0.2e-3];
  
 %constraints %constraints
-A = [diag([1 1 1 1]); diag([-1 -1 -1 -1])]; +b1 = [0.05; 0.05; 25e-3; 0.1e-3];   % Lower bound (b1 < x) 
-b = [0.2 0.2 75e-3 1e-3 0.05 0.05 25e-3 0.1e-3]';+b2 = [0.2;  0.2;  75e-3; 1e-3  ];       % Upper bound (x < b2) 
 + 
 +A = [-eye(4); eye(4)]; 
 +b = [-b1;b2];
  
 %optimization %optimization
Line 116: Line 119:
  
 %show results %show results
-run_sim(x_opt,false)+[cost, out] = run_sim(x_opt,false);
 </code> </code>
 +//Note: prescribing input rotation is only supported for SPACAR light version 1.27 or higher.//
optimization.1537259579.txt.gz · Last modified: 2018/09/18 10:32 by mark.naves

Page Tools

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki